Sampler Parts

Composite ProPak kit.  Includes 100 composite 2 Gallon (7.5 Liter) ProPak bags, holder with cap and o-ring. Note:  This item replaced 602953029. This item has a lead time of 12-16...

Controller used on 3710 Full-Size and 3710C Compact Portable Samplers.  Includes pump tubing. This item has a lead time of 28-32 days

Refrigerator door gasket for Model 4700 or 5800 Samplers. This item has a lead time of 1-5 days

Old style stainless steel strainer for 3/8 inch I.D. tubing.  Four piece stainless steel strainer. Dimensions: Length:  9-1/4 inchesDiameter:  1-3/8 inches This item has a lead time of 12-16 days

Set of 24 wedge shaped polyethylene bottles with caps, 500 mL capacity. Bottle Dimensions:Height:  7.75 Inches (19.69 cm)Throat:  0.93 Inches (2.38 cm) Note:  This replaced part number 602903006. This item...

Caps for 1 Liter polypropylene wedge-shaped bottles and1 Liter wedge-shaped ProPak holders, quantity 100. This item has a lead time of 3-7 days

Distributor arm for 6700 Series Samplers.  Used on portable full-size, compact and fiberglass refrigerated versions.  Two-piece and adjustable dependent on the bottle configuration used.  Other hardware required to complete mounting....

Replacement pump motor kit for the Models 4700 and 5800 Refrigerated Samplers.  Includes the following: Replacement pump motor Cable tie, 14.5 inches long This item has a lead time of...

Discharge tubing used on Teledyne ISCO vacuum samplers, 5 ft. length. Note:  This tubing is the same as WW050, only in a bulk roll. This item has a lead time...

Controller used on GLS Sampler.  Does not include pump tubing. This item has a lead time of 19-23 days

Replacement wiring harness kit for the Model 5800 Sampler.  Includes the following: Pump interface circuit board assembly Interface communication harness Distributor sensor wiring assembly Interface cap gasket Pump sensor wiring...

Rubber draw latch kit.  Includes 3 each flexible EPDM black rubber handles.  Kit does not include rivets or brackets. This item has a lead time of 5-9 days

TIENet™ 301 pH and temperature sensor interface with 32 ft. (10 m) cable.  For permanent Signature meter.  Includes pH and temperature sensor with 25 ft. (7.6 m) cable, calibration buffers...

Polyethylene round bottle with two caps, 5.5 Gallon (20.5 Liter) capacity.  Includes two caps - one solid cap, the other modified with a hole to properly route the discharge tube during...

Capacitor and relay kit for Model 4700 or 5800 Sampler. This item has a lead time of 3-7 days

Replacement fiberglass refrigerator temperature control small parts kit.  Includes the following: Potentiometer Knob package This item has a lead time of 3-7 days

Bottle cap used on 2.5 Gallon polyethylene bottle. This item has a lead time of 1-4 days

Caps for 500 mL polyethylene wedge shaped bottles, quantity 100. This item has a lead time of 12-16 days

Set of 500 wedge-shaped polypropylene bottles with caps, 1 Liter capacity. Bottle Dimensions:Height:  10.15 Inches (25.8 cm)Throat:  1.62 Inches (4.12 cm) This item has a lead time of 12-16 days...

Replacement pump gear case assembly kit for 3700, 3700C, 3710, 3710C, GLS and Glacier Samplers.  Includes the following: Pump rotor assembly Pump housing assembly, inside Pump housing assembly, outside Appropriate...