Repair Parts (Signature LaserFlow®)

Front panel label with built-in keypad assembly for Signature® Flowmeter. Estimated Shipment Time (After Receipt of Order):  7 Day(s)

Cord grip fitting for cable diameters from 0.250 to 0.375 inches (6.35 to 9.53 mm).  For user-supplied cables within this diameter range. Estimated Shipment Time (After Receipt of Order):  7...

Cord grip fitting for cable diameters from 0.375 to 0.438 inches (9.53 to 11.13 mm).  Accommodates the passage of wide cables into the Signature® meter housing.  This includes TieNet™, power...

Bottom connector plug for Signature® Flowmeter.  Used to seal unused cable entry ports on the bottom of the meter.  Ensures IP66 protection.  Manufactured of black Delrin plastic. Estimated Shipment Time...

Kit for replacement of USB hub on Signature® Flowmeter.  Includes the following: Micro USB assembly Micro USB strap Micro USB cap Retaining ring Appropriate o-rings Estimated Shipment Time (After Receipt...

Power supply assembly used on Signature® Flowmeter. Estimated Shipment Time (After Receipt of Order):  7 Day(s)

Fuse, 3.15 Amp, 250 volt Slo-Blo. Estimated Shipment Time (After Receipt of Order):  7 Day(s)

Fuse (4.0 Amp / 250 VAC / Time Lag Slo-Blo). Estimated Shipment Time (After Receipt of Order):  7 Day(s)

Signature® Flowmeter Voltage Stabilizer.  This alteration allows for solar chargers with voltage outputs higher than 14.25 VDC to be used with the Signature® Flowmeter.  Solar charge regulators consistently exceed 14.25...

Liquid crystal display (LCD) module.  Used on the Signature® Flowmeters. FSTN positive transflective with white light-emitting diode (LED) backlight.  Graphic controller integrated circuit (IC) not included. Number of dots:  320...

Secure digital 8-pin microSD flash card.  Used on Signature® Flowmeters, 3.3 volt. Estimated Shipment Time (After Receipt of Order):  7 Day(s)

Coin-style lithium battery 3 Volt, 220 milliampere hour. Standard discharge current 0.3 mA.   Compatible with: D-Series Syringe Pump controllers Signature® Flowmeters CombiFlash® EZ-Prep CombiFlash® Rf CombiFlash® Rf+ CombiFlash® Rf-75 CombiFlash® Rf-150...

TIENet™ Noise Reduction Service Kit.  This kit contains enough items to resolve noise on 3 sensor and 4 analog outputs. NOTE:  This kit is for Signature® serial numbers prior to...

Solenoid valve, 12 VDC.  Continuous duty 2-way solenoid valve, 0-100 psig pressure range.  Used on the Signature® Bubbler Flowmeter, ACCQPrep®, CombiFlash® EZ-Prep, CombiFlash® NextGen 300 and CombiFlash Torrent® Systems.  Estimated...

Replacement LaserFlow® mounting handle kit. Estimated Shipment Time (After Receipt of Order):  7 Day(s)

Horn used on Model 360 LaserFlow® Sensor, blue. Estimated Shipment Time (After Receipt of Order):  1 Day(s)

Replacement small parts package kit for LaserFlow®.  Includes the following: Probe cap (male) Probe plug (female) Stainless steel shackle with screw pin, 5/16 Inch Appropriate o-rings and screws Estimated Shipment...

LaserFlow® Ex mount / handle replacement kit.  Includes appropriate pins, screws and washers. Estimated Shipment Time (After Receipt of Order):  7 Day(s)

Horn used on Model 360 LaserFlow® Sensor, black. Estimated Shipment Time (After Receipt of Order):  7 Day(s)

Replacement LaserFlow® vertical mounting components kit for permanent wall mount.  Includes the following: Vertical wall mount with bracket Wall mount bracket Vertical coupling tube clamp (right) Vertical coupling tube clamp...