Flowmeter Parts

Desiccant, 16 oz. bottle.  Loose yellow / orange silica gel beads (2 to 5 mm), which turn green when saturated.  Used in 2100 Series Module desiccant tubes, 4200 Series Flowmeters,...

Front panel label with built-in keypad assembly for Signature® Flowmeter. Estimated Shipment Time (After Receipt of Order):  7 Day(s)

TIENet™ 308 Analog 4-20 mA Output Option Card, two independent channels.  Provides an analog output signal proportional to a configured measurement input.  Up to three cards may be installed in...

Vinyl bubble line, 1/8 inch I.D. x 1/4 Inch O.D., 100 Ft. (30.4 m) long.  For use with bubbler flowmeters/modules. Note:  This item replaced part numbers: 601873044601873051605304706 Estimated Shipment Time...

USB cable, 3 In. (75 mm).  USB Micro A to USB A for Flash Drive connection to Signature® meter. Estimated Shipment Time (After Receipt of Order):  14 Day(s)

Signature® desiccator assembly with desiccant and hydrophobic filter. Estimated Shipment Time (After Receipt of Order):  14 Day(s)

Air pump replacement kit for Signature® Bubbler Flowmeter. Estimated Shipment Time (After Receipt of Order):  7 Day(s)

TIENet™ 306 sampler interface cable, 32 ft. (10 m).  For permanent Signature® meter.  Includes one TIENet™ cord grip fitting for watertight connection to the Signature® meter in non-conduit applications.  Connects...

TIENet™ 304 Contact Output Option Card, two isolated independent Form "C" relay circuits.  Card closes or opens relays at specific thresholds set within the Signature programming.  Up to three cards may...

Kit for replacement of USB hub on Signature Flowmeter.  Includes the following: Micro USB assembly Micro USB strap Micro USB cap Retaining ring Appropriate o-rings Estimated Shipment Time (After Receipt...

TIENet™ 306 sampler interface cable, 32 ft. (10 m).  Connects to the Model 4700 or 5800 Refrigerated Sampler 16-pin connector to support sampler pacing and enable functions.  Includes one TIENet™...

TIENet™ 310 Ex Ultrasonic Sensor with 32 ft. (10 m) cable.  Includes one TIENet™ cord grip fitting (part number 209007312) for watertight connection to the Signature® meter.  Suitable for monitoring...

Wall mount bracket for 710, 2110, 3010, 4210 and TieNet™ 310 Ultrasonic Level Sensors.  Manufactured of 302/304 stainless steel. Estimated Shipment Time (After Receipt of Order):  14 Day(s)

Spring Ring for 15 inch diameter pipe.  Used to install ISCO sensors.  The spring ring will accommodate one of our sensor carriers and can be used to mount one sensor...

TIENet™ 301 pH and temperature sensor interface with 32 ft. (10 m) cable.  For permanent Signature® meter.  Includes pH and temperature sensor with 25 ft. (7.6 m) cable, calibration buffers...

Battery backup kit for Signature® Flowmeters.  Includes Model 946 Lead Acid Battery, adapter cable and mounting hardware. Estimated Shipment Time (After Receipt of Order):  14 Day(s)

Sensor mounting plate.  Flat plate for mounting up to three sensor in rectangular, trapezoidal or irregular channels.  Includes plastic ties to fasten the sensor cable and installation instructions.  Requires carriers...

Scissors Ring for 16 to 36 inch diameter pipe.  Used to install ISCO sensors.  Includes base section, scissors mechanism, one pair of 7.5 inch extensions and one pair of 20...

Spring Ring for 8 inch diameter pipe.  Used to install ISCO sensors.  The spring ring will accommodate one of our sensor carriers and can be used to mount one sensor...

Maintenance kit for 2191 Battery Module.  Includes: O-rings for connectors, 3 each Gaskets for battery doors, 2 each Desiccant bag (16.5 gram), 2 each Humidity indicator card, 2 each Estimated...