Flowmeter Accessories

Plotter paper roll for 4200 Series Flowmeters, 58 ft. long.  Also known as chart paper. Frequently ordered with plotter paper: Printer Ribbon for 4200 Series Flowmeters, black This item has...

Printer ribbon for 4200 Series Flowmeters, black. Frequently ordered with printer ribbons:  Plotter Paper for 4200 Series Flowmeters This item has a lead time of 1-3 days

Model 934 Nickel-Cadmium Battery.  Rechargeable, 12 VDC, 4 Amp-hours.  For use with ISCO GLS, 3700 & 6700 Series Portable Samplers and 4200 Series Flowmeters.  Recharge using one of these chargers:...

Model 913 High Capacity Power Pack.  Converts 120 VAC to 12 VDC.  Includes separate output for charging ISCO Model 934 Nickel Cadmium Batteries.  For use with GLS, 3700/6700 Series Portable...

External 12 VDC connect cable, 6 ft.  For powering portable ISCO Sampler or Flowmeter from an external 12 VDC source such as an automotive or deep cycle marine battery.  Terminates...

Model 961 Battery Charger, powered by 120 VAC, 60 Hz.  For charging ISCO 934 Nickel Cadmium Batteries, one at a time. This item has a lead time of 5-9 days...

Model 946 Lead-Acid Battery.  Rechargeable, 12 VDC, 6.5 Amp-hours.  For use with ISCO GLS, 3700 & 6700 Series Portable Samplers, 4200 Series Flowmeters and Signature Portable Flowmeters. Recharge using one of...

ISCO Sampler to ISCO Flowmeter connect cable, 25 ft. (7.6 m).  Note:  For interfacing a Signature flowmeter to ISCO Sampler, purchase appropriate TIENet 306 Sampler interface. This item has a...

USB cable, 3 In. (75 mm).  USB Micro A to USB A for Flash Drive connection to Signature® meter. This item has a lead time of 1-3 days

USB communication cable, 10 ft. (3 m).  Connects 2100 Series Module top connector to PC with USB connector. This item has a lead time of 5-9 days

Ethernet communication module for Signature® meter.  Provides RJ45 connection to support Ethernet communications.   This item has a lead time of 12-16 days

Vinyl bubble line, 1/8 inch I.D. x 100 Ft. (30.4 m).  For use with bubbler flowmeters/modules. Note:  This item replaced part numbers 601873044 and 601873051. This item has a lead...

Desiccant, 33 gram bag.  Used in 3700 Series Sampler Controllers and 2191EX battery module caps.   This item has a lead time of 1-3 days

TIENet® 308 Analog 4-20 mA Output Option Card, two independent channels.  Up to three cards may be installed in a Signature® meter for up to six independent analog output channels. ...

Non-ISCO flowmeter connector only.  Allows connection of a non-ISCO flowmeter to an ISCO sampler.  The flowmeter must produce a dry contact closure proportional to flow rate. This item has a...

Stainless steel bubble tube - 4 ft. (1.21 m) length.  For use with 1/8 inch I.D. vinyl bubble line. This item has a lead time of 12-16 days

Scissors Ring for 16 to 23 inch diameter pipe.  Used to install ISCO sensors.  Includes base section, scissors mechanism, and one pair of 7.5 inch extensions.  The base section of...

Reroll spool assembly.  Used on 4200 Series Flowmeters. This item has a lead time of 1-4 days

Teledyne ISCO Open Channel Flow Measurement Handbook is a valuable resource for those involved with flow measurement applications. This new eighth edition combines material from many sources, providing information on...

Spring Ring for 15 inch diameter pipe.  Used to install ISCO sensors.  The spring ring will accommodate one of our sensor carriers and can be used to mount one sensor...